JIS B 6402 PDF

Read 3 answers by scientists with 1 recommendation from their colleagues to the question asked by Daniel Martinez Krahmer on Dec 17, JIS B Mechanical power presses — Testing of the accuracy (FOREIGN STANDARD. Find the most up-to-date version of JIS B at Engineering

Author: Zulkigal Brazilkree
Country: Guyana
Language: English (Spanish)
Genre: Video
Published (Last): 12 July 2009
Pages: 128
PDF File Size: 15.37 Mb
ePub File Size: 3.66 Mb
ISBN: 703-4-38186-270-2
Downloads: 52778
Price: Free* [*Free Regsitration Required]
Uploader: Digami

Evaluation of the screw press capacity is made with testing a work piece in cold compression. Set up the press slide speed and the slide stroke as maximum adjust to maximum power. In this status, compress the testing work piece and detect the frame deformation through strain gauge to show kN value on a load gauge.

The screw press of kN; Set the load gauge that shows figures of when the testing work piece is compressed with the equivalent of kN.

In other word, as the compression value for the testing piece is criterion, set the figures of equivalent amount on the load gauge.

When you set up two strain gauges at each side of the frame, the load on one side frame equals to a half of the load becomes 4602 value and shown as certain kN in RH and LH independently, plus total kN in the display. Two independent load display for each side simply shows one sided load and the total load is defined as screw press load. In case of the operation, hard-on-hard, in which striking die against die with the same condition as the above item?

Frame is stretched by three times This three time figure shows the maximum applied load of the press.

In screw press, the flywheel revolution energy is consumed one hundred percent in each press cycle. It is just a matter of revolution energy usage whether it is used for work piece compression or the frame deformation. During work process like vertical compression of heated bar material, the energy is consumed for plastic deformation of the material mostly and the frame bears very small amount of load shown low value on the load gauge.

On the contrary, cold working stamping or stamping of steel plate with many edge burrs indicates large figures on the load gauge even if energy adjustment is relatively small. Machine life is drastically shortened if the press is used under three more times of nominal capacity maximum capacity repeatedly usually, the screw and the frame get damage. Because the press is designed to deform product, not for assuming of crashing tools themselves repeatedly.

  ATEN IC485S MANUAL PDF

Here a problem occurs how much the allowable applied load of a press being set witch coming from rigidity design of machine. Even though frame is the same, larger amount of flywheel energy is put on to be a large performance press for hot forging and smaller amount of flywheel energy is put on to be a small performance press for cold forging.

Kaushico Machine Tools Pvt. Ltd.

The allowable performance for the former is 1. Surely, it is possible, however, can you imagine and would like to have the screw press that has the frame of kN press with flywheel of 6042 press and is used as nominal capacity of kN press?

It becomes quite expensive machine though we could manufacture it.

There are always risks that the load surpasses the allowable load. Since the screw press has no mechanical lower-dead-point, the machine never stops caused from overload stick like the crank press machine.

That means that there exists a risk that the machine is used under overload situation without knowing. Therefore, jls press needs to have emergency stop mechanism if the overload happened.

We mis taking the method that the machine gives warning signal to operator through LED lamp when the machine is in overload emergency stop status from electric signal of the load gauge. We don’t use the torque limiter approach attached to the flywheel discharging overload energy.

It’s hardly recognizable to the operator if the torque limiter functions under the overload condition. His company does not employ this method because in case of hardened spring adjustment of the torque limiter by mistake, machine may always jsi with overload and finally machine may brake. Forming energy is completely same with flywheel energy.

Also, these are proportional to slide descending speed, too. In the screw press, generally, the forming energy is adjusted with slide speed control just before stamping. Attention is required that there is no relationship or relativity between the forming energy and the load display.

You may recognize from the above discussion that the load gauge display quite differs when smash up a test piece or strike die against die even if the forming energy is the same. The load gauge simply displays the result of how many kN loaded to the frame. You can adjust the slide speed freely adjustable forming energy freelyhowever, you can’t control how many kN to strike.

  CRACKING THE CODING INTERVIEW GAYLE LAAKMANN 5TH EDITION PDF

Naturally, if you form product under the same condition, the slide speed adjustment is proportional to the load gauge display. The slide speed adjustment takes the method that controls to have same speed every cycle based on encoder signal detected the slide descending speed. The required speed is previously set on touch panel or by setting dial.

If the preset value is small, the slide is clutched off right after acceleration and it descends evenly with inertia.

SPECIFICATIONS MODEL : ‘ESR’

Its control is where the point to clutch off, not revolution control like inverter motor. The flywheel revolution is sequentially controlled in a servomotor direct driven system without clutch transmission. Acceleration and speed reduction are combined automatically to apply power with the Minimum time for one cycle. Especially, in those large edge burrs and cold working, it could become out of the allowable load even if the forming energy value is still a half of it.

The capacity of screw press should be used with the nominal capacity. Using the allowable capacity is disputable from the point of fair business transaction. As explained earlier, the press can compress a test piece with nominal capacity, however, it is absolutely impossible to do with the allowable capacity.

Basically, eccentric load out of the screw diameter should be avoided. The load that can be allowable becomes reducing when it becomes far from the center. The load should be placed on the center fundamentally.

We are taking the method that the machine gives warning signal to operator through LED lamp when the machine is in overload emergency stop status from electric signal of the load gauge note We don’t use the torque limiter approach attached to the flywheel discharging overload energy.